This is an OEM Honda part manufactured for use with small engines. This rubber grommet is used to provide a seal to allow fuel lines to pass into and out of the fuel tank without leaking. Overtime fuel can deteriorate the grommet, so replacing it can ensure a good seal. The grommet is sold individually, please see model diagram for additional parts.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
was a honda part and not aftermarket
well packaged and fit without any problems
Guest - April 22, 2020
Verified Purchase
★★★★★
★★★★★
Engine replacement grommet
The replacement parts I ordered worked perfectly for me. I am very happy with ereplacementparts products.
Guest - July 18, 2020
Verified Purchase
★★★★★
★★★★★
Tiller is running like a champ
Got all the right parts, quick delivery and all is good now.
Guest - May 18, 2021
Verified Purchase
★★★★★
★★★★★
Difficult , ended up not using it
It didn't have the plastic feed through tubes installed, I try ed to remove the old ones from the old grommet and they wouldn't come out. I was worried I would break them. I tried a little heat and lubricant didn't bulge.
Guest - June 27, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed air cleaner assembly.
2. Removed throttle cable from carb.
3, Removed rope pull start and fuel tank.
4. Removed fuel lines from tank, making sure to mark where they go.
5. Removed fuel tank grommet and filter and replaced with new ones.
6. Removed carb and replaced with new one.
7. Install fu
... Read moreel tank, rope start, hook up fuel lines, attach throttle cable and air filter assy, fill with fuel, prime carb and start engine, done.
(Fuel tank grommet very hard to get out, you will need strong hands. When re-installing fuel tank grommet make sure both plastic through tubes are in the grommet and use a little dielectric grease on the grommet to insert it back into the tank. Very hard to insert it so be careful.)
Read less
Did you find this story helpful?
Thank you for voting!
Fuel tank cracked, fuel filter corroded, fuel lines brittle.
1. Removed the fuel tank.
2. Removed and cleaned the carburetor.
3. Drained the oil.
4. Installed 2 fittings in the grommet.
5. Hook up fuel line with the fuel filter.
6. Attached the grommet with fittings into the fuel tank.
7. Attached the fuel tank into the body.
8. Attached the fuel lines from
... Read more the carburetor into the fuel tank.
9. Secure the carburetor into place with bolts.
10. Attached clutch line into the carburetor.
11. Fill the oil tank with oil.
12. Remove the tines to pump grease into transmission body.
13. Reinsert the tines.
14. Check and clean the spark plug.
15. Fill the tank with gas.
Choke the engine... start the engine....Broooom!!!! 1 Pull and it started immediately.....after warming up the engine, my old Honda FG1001A sounded like a brand new machine with power when revved up.
Read less
Did you find this story helpful?
Thank you for voting!
Engine servicing, tune-up, repairs to fuel primer bulb and fuel lines
Basically, all of the servicing and repairs were done with the help of You Tubers. I was able to follow the videos and able to to the work on my Honda Gas Trimmer with also help of eReplacement videos posted. All the parts purchased from eReplacement were correct and very easy to install.
Thank you eReplacementParts!
Did you find this story helpful?
Thank you for voting!
Carb on small tiller was clogged and had been setting up for three years
Simply removed old fuel lines and grommet replaced with new parts and it runs perfect and does not leak.
One note that is important is to insert fuel lines into grommet first then you can cut lines to length after putting grommet back into your tank.
1. put mower up on sawhorses to avoid bending over so much
2. removed air filter, starter assembly and fuel tank. Took pictures from several views
3.removed controls assembly and carburetor
4. made two dowels of steel rod to assist in reassembly. Would have preferred two 6mm threaded
rods which i did not hav
... Read moree. Placed rods in head mounting holes
5. replaced various parts and control assembly on guide rods. Removed steel rods and
replaced long mounting bolts Checked pictures for correct reassembly
6. replaced fuel lines, fuel tank, starter assembly
7. took down from sawhorses and filled fuel tank.
8. started up and ran just fine with two pulls at full choke. Idled well also. No carb adjustment.
Your parts list did not include carburetor -- probably referred to my previous repair of Honda tiller. My description above was for Honda lawnmower!!=ƒÿÄ
Read less
Did you find this story helpful?
Thank you for voting!
The fuel filter tube was rotted and the filter was clogged
The repair was simple enough. One problem solved and another created.
The machine runs well for a time and then stalls out because the fuel supply dries up. I then have to re-prime the carburetor with the bulb.
Starting the machine when it\'s cold sometimes requires that I pull the plug and inject some fuel into the cha
... Read morember. Then it will start and run.
Not enough vacuum on the intake stroke? Clogged line or filter? Clogged Jet or damaged diaphragm? Don\'t know. Thought I replaced everything that needed replacing.
Engine
- Honda Small Engine Model GX25NTSMTD Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Hose or Tube","title":"Hose or Tube","url":"/parts/lawn-and-garden/engine/hoses-and-tubes/"},{"position":2,"name":"17504-ZM3-003","title":"17504-ZM3-003","url":""}]
(VIN_FZCV-6000001_to_FZCV-9999999)_WW_10.gif "Part Location Diagram of 17504-ZM3-003 Honda Fuel Tube Grommet")
(VIN_FZCV-6000001_to_FZCV-9999999)_WW_10.gif "Part Location Diagram of 17504-ZM3-003 Honda Fuel Tube Grommet")
