OEM Porter Cable Electric Drill Parts & Accessories

$7.42

Manufacturer Part Number:: 176846-04

This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that c...

Terminal

$6.16

Manufacturer Part Number:: 444262-00

This is a replacement part directly sourced from the manufacturer for use in drills, hammers, grinders, sanders, jigsaws, and trimmers made by DeWALT, Porter Cable, Black & Decker, and Bostitch. It connects to the power cord and is made out of metal. This part is extremely small and will need to be replaced if it becomes lost or if it breaks. The terminal is sold individually.

Keyless Chuck

★★★★★

(8)

$54.87

Manufacturer Part Number:: N196034

Spend less time changing bits and more time getting the job done. This keyless chuck is all about efficiency, offering tool-free operation with a reliable ratcheting mechanism. Ideal for busy professionals or DIYers who value speed, versatility, and simplicity in one smart upgrade. This is a 1/4 inch keyless chuck.

STRAIN RELIEVER

★★★★★

(26)

$12.02

Manufacturer Part Number:: 901266

This is a genuine Porter Cable replacement part, it is sold individually. A Cord Strain Reliever is used on most all power tools. It purpose is to reduce the bending of the cord as it comes out of the housing, which otherwise would cause the cord to crack and wear.

BEARING

$14.92

Manufacturer Part Number:: 859293

This is a needle bearing that is open on both sides. This genuine Porter Cable replacement part is sold individually. • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it to run smoothly. • Bearin...

Gear

★★★★★

(2)

$15.13

Manufacturer Part Number:: N437049

This is a genuine replacement part that has been sourced from the original manufacturer to be used with electric drills from DeWalt, Black and Decker, and Porter Cable. The metal gear is used to link the armature assembly and the chuck's spindle shaft. This item is priced as a single item.

BRUSH & SPRING

★★★★★

(2)

$11.50

Manufacturer Part Number:: N119739

Genuine Porter Cable replacement part Includes 1 Carbon Brush with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear it...

F/R ACTUATOR

★★★★★

(5)

$6.81

Manufacturer Part Number:: 90569693-03

BRUSH & RETAINER ASY

★★★★★

(1)

$16.68

Manufacturer Part Number:: 874289

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of t...

Power Cord

★★★★★

(75)

$27.42

Manufacturer Part Number:: 330072-98

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...

BRUSH

★★★★★

(6)

$13.28

Manufacturer Part Number:: 690741

Genuine Porter Cable replacement part rnIncludes 1 Carbon Brush with lead.rnrn n++ Worn brushes are often the cause of a poorly running motor n++ Replacing brushes can fix an intermittent motor n++ New brushes can restore a motorn++s electric braking Carbon motor brushes are one of the most commonly replaced power tool components.n++ Because carbon brushes are wear items, meaning that through...

Ball Bearing

★★★★★

(1)

$9.09

Manufacturer Part Number:: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

Porter Cable Electric Drill Parts

Top Porter Cable Electric Drill Models

Popular Porter Cable Electric Drill Parts

Porter Cable Electric Drill Models

Porter Cable Electric Drill Parts

Search By Model or Part Number

Top Porter Cable Electric Drill Models

Popular Porter Cable Electric Drill Parts

Porter Cable Electric Drill Models