This is a genuine Husqvarna replacement part, it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Exact fit
Exact fit. Accurate part and expedient delivery.
Jerry - June 12, 2019
Verified Purchase
★★★★★
★★★★★
Easy repair
Great
Guest - June 10, 2019
Verified Purchase
★★★★★
★★★★★
Exact Replacement
Part received quickly after an easy order process. Once you enter brand and model the parts list presents itself nicely. Price is competitive to local dealers.
Guest - June 11, 2019
Verified Purchase
★★★★★
★★★★★
Husqvarna weed wacker filter
Fit like a glove. The cover was a perfect fit too.
Greg - June 22, 2019
Verified Purchase
★★★★★
★★★★★
easy repair
Intake air filter was a simple 30 seconds replacement
Guest - June 27, 2019
Verified Purchase
★★★★★
★★★★★
needed part
quick delivery, worked to perfection, weed eater working like new.
Guest - July 6, 2019
Verified Purchase
★★★★★
★★★★★
Maintenance problem solved
Needed this filter, tried shopping at store where machine was purchased, no luck. One minute on e-replacement and it is on the way. Received quickly fits perfect.
Guest - November 25, 2019
Verified Purchase
★★★★★
★★★★★
Exact Part Ordered
My weed eater is working like new again, thanks.
Guest - June 11, 2023
Verified Purchase
★★★★★
★★★★★
Perfect fit.
The filter, cover for aircleaner cover and nut screw. Fits perfectly. Thank you!
Guest - August 27, 2023
Verified Purchase
★★★★★
★★★★★
quick shipping,,,, good product
good product, reasonable price
Guest - August 4, 2023
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Repair was simple. Most difficult part was replacing fuel and return lines. Cut lines at an angle, put oil on them, push through hole and grab with a pair of hemostats and pull. Not sure pliers would work. Other than that simple.
Did you find this story helpful?
Thank you for voting!
Would not start. Carburator was plugged up and would not deliver fuel with plunge bulb. Tried carb and choke cleaner. Spark was good.
1st Drain remaining fuel and discard. Unpacked the new parts and familiarized with all.Took off cover with nut driver. Discarded used air filter and replaced it with the new one and set it aside. The throttle cable and fuel tubing were removed with needle nose pliers. Removed the old carburetor. Removed old gasket and installed the new.
... Read moreReplaced the old carb with the new. Without cover the carb is loose for attaching the throttle cable first and then the fuel tubing. Used needle nose pliers to attach the throttle cable and to attach the tubing to the new carb and carefully slid them up snug to the carb. Tested the throttle and it worked properly. Replaced cover. Tightened cover nuts with nut driver. Added fresh oil and gas mix. Pumped the new plunge bulb about 4 to 6 times, with no throttle pulled 2 times at full choke, and then on 3rd pull at half choke it fired up. I let it warm up for10+/- seconds and flipped off the choke. Idle is slightly high but haven\'t changed it with the idle adjust screw yet. Went right work and it ran for about 2 hours like it was brand new.
Not very difficult. Removed gas tank. Pried fuel line from tank. Pulled fuel filter from existing fuel line and installed on new fuel line. Pushed new fuel line into tank and reinstalled tank. Worked perfectly!
Did you find this story helpful?
Thank you for voting!
broken trottle cable. broken trigger spring and trigger
1. took screws out of trigger holder
2. took screws out of shaft
3. took carburetor cover off
4. disassembled throttle cable and replaced
5. replaced trigger and spring and rerouted in housing and replaced all screws
6. fired that baby up!
Removed filter
Removed two nuts
Removed fuel lines
Removed throttle control removed gasket
Began replacing new parts in reverse order of removal
Primed system
Followed starting instructions
Began using
Did you find this story helpful?
Thank you for voting!
Huskquvnara line trimmer wouldn\'t start or if did would not stay running.
1. Emptied gas tank.
2. Removed air filter cover and air filter.
3. Cut and removed old fuel line and assembly pick up.
4. Fed new fuel line into gas tank and attached assembly pick up. Fed new fuel return line.
5. Cut and attach ends of fuel lines to carburetor.
6. Replace air filter/cover.
7.
... Read moreRemoved starter assembly (torx bit).
8. Install new starter assembly.
Read less
Did you find this story helpful?
Thank you for voting!
The trimmer would noy prime properly and when I could get it started the trimmer would not idle.
1) Remover air filter cover and air filter.
2) Take the 2 nuts off that secure the air filter housing to the engine. Remove the 2 screws on the primer bulb and replace.
3) Remove the primer and fuel line from the tank and carburetor.
4) Install the fuel filter to the fuel line and reinstall in the tank. Attach the lines
... Read moreto the carburetor.
5) Reinstall air filter housing, filter and cover.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 530150253 Husqvarna Trimmer Filter")
_WW_1.gif "Part Location Diagram of 530150253 Husqvarna Trimmer Filter")
