1. Removed 4 or 5 Philips screws from handle (nuts stayed in removed handle piece)
2. Removed 2 screws holding tension on cords end the one holding switch to saw
3. Un-screwed wire from switch (black wire white wire) remember which wire goes where
(white wire was on side of switch with part #s or something
... Read more> BACK TOGETHER
1. Attach new cord to switch remembering wirers have to be in the same place as removed
2. Replace restraining clip and 2 screws and tuck all wires in to saw
3. Replace handle part watch that nuts stayed in place
4. Inspect job should look just like it did but with shinny new cord
PLUG IT IN, PULL TRIGGER (remember it IS a SAW and be careful )
1. Removed 4 phillips head screws to remove handle assembly from saw.
2. Removed 5 phillips head screws to open handle assembly and provide access to wiring
3. Removed power cord and its connection to a connector component and the switch.
4. Cut new wires as needed to make connections
5. Noted that the new s
... Read moretrain relief was not the correct size. Discovered that this was due to the labeling on the miter saw which indicated that it was a model LS 1030 when it was actually a model LS 1030N. Was able to determine this from drawings which were accurate.
6. Used old strain reliever which was in good condition
7. Then disaster: One of the handle assembly screws fell into the armature casing. The armature unit could not be removed as it appeared to be stuck in the casing. This condition has been reported by others. After a couple of days trying magnets, shaking the casing, using wires, etc. I finally was able to see where the screw was stuck with a flashlight shining on the casing air vents. Once seeing the screw I was then able to remove it.
8. Then took a little time to discover how a retention spring functioned together with the safety release button on the unit.
9. Voila! Repair complete and the saw started and has been resurrected from the dead!!
Remove the screws from the housing
Remove the cord clamp
Remove the cord wires from the switch
Put strain relief on the new cord
Connect the wire the switch
Install the cord clamp
Put the housing back together
Remove the handle cover to expose the cord, remove the two screws from the cord hold. Remove the cord leads from switch. It is easier if you remove the switch too. Slide off the cord relief and place it on the new cord. The cord does not include terminals for the switch. Attach cord to switch, replace switch and cord hold with the two scr
... Read moreews. Attach handle half
Read less
Did you find this story helpful?
Thank you for voting!
Had to replace the power cord my Makita compound miter saw is 16 years old and is the best saw I have ever owned it quit running on me one day and I figured out that it might be the power cord.
Had to remove the handle cover, then the cord clamp. I then removed the cord wires from the switch and discarded the old cord. I removed the strain relief from the old cord and placed it on the new cord. Then connected the cord leads to the switch. And attached the cord clamp.Then replaced the handle cover. I pressed the switch button int
... Read moreo the motor housing. Then I removed the small screw from the broken lever, and install the new lever.
Read less
Did you find this story helpful?
Thank you for voting!
Repaired power cord, brushes and replaced flange nuts
Removed half of the switch handle, Remove two screws from cord holder, removed the the cord wires from the switch, cut the cord leads to the correct length, had to locate two terminals to put on the end of the cord leads. Attached cord leads to switch.don\'t for get to put the old cord relief back onto the new cord. reattached the cord ho
... Read morelder with the two screws. Then replace the handle half. For the brush set, I removed the brush caps, then removed the old brush set and installed the new set and the brush caps. I also replaced the inner and outer flanges, and the blade bolt.
Separated handle and trigger section. This required removal of 5 screws. This exposed the wire connections. Removed old wire. It had a wire connector, sleeve type from a previous repair. This had to be reconnected. Threaded the wire thru the rubber wire protector. Made all connections, reassembled and tested. I put this off for ages. I ha
... Read mored tried to fix it with electrical tape. Doing it right is always best!
Remove on half of the switch handle
Remove the cord clamp
Disconnect the cord wires
Remove the cord relief from the old cord to the new cord
Connect the cord wires
Attach the cord clamp
Replace the handle half
Take off the handle, take off the cord holder, take off the cord wires to the switch.
Slide the new strain relieve onto the new cord. Cut the cord wires to the correct length. connect the cord wires to the switch. Screw the cord holder on. Screw the handle on.
Did you find this story helpful?
Thank you for voting!
Switch would not turn off ,cord was getting frayed
Remove screws in saw handle ,cord restraint, and last screws in switch. Remove screws from motor leads. I had to obtain terminal ends for the cord before proceeding. After reattaching motor leads and cord with new cord guard it was an easy job to reassemble switch and cord into saw handle.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10153842
Manufacturer Part Number: 664265-4
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
