OEM Delta Chop Saw Parts & Accessories

Anti-kick Finger

$6.16

Manufacturer Part Number:: 424040470002S

This is an authentic OEM part which is made for use with Delta radial arm saws. The device is used to prevent the material from being shot toward the user in the event of kickback. It provides a high-quality replacement for a damaged or a missing component that was installed on a new unit. Check the owner's manual and the diagrams for your model to ensure the correct repair procedure. Note, it is ...

Geared Tooth

★★★★★

(3)

$31.08

Manufacturer Part Number:: 424020510008

This is a genuine OEM sourced replacement part designed for use with Delta radial arm saws. It is an important part of the adjusting mechanism. This gear is made out of plastic and it is sold individually. To complete this repair you would need a screwdriver and a wrench set. • First you want to positions saw on its side • Punch out roll pin holding the gear on • Remove old gear • Inst...

Fibre Washer

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 904070105571S

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Delta saws. This is a special component that is utilized to provide a tight seal between connected components, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. It is an identical replacement for a missing or a faulty wash...

Roll Pin

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 905010102732S

This is an authentic Delta replacement part sourced directly from the manufacturer. The roll pin is found in several different machines from Delta. This part is made of metal, and is put to different uses in the machine, depending on model. Please refer to the parts diagram to be sure of ordering the correct part. This part is sold individually.

Special Bearing

$321.31

Manufacturer Part Number:: 920101514919

This is an original part assembled by the original manufacturer. It is commonly used in Delta radial arm saws. Ball bearings are used to buffer metal parts and to take wear for them. Therefore they are replaced fairly often due to metal fatigue. They also serve to secure parts to ensure proper movement direction and position. Sold individually.

Bolt

$6.16

Manufacturer Part Number:: 901010605768S

BRUSH

★★★★★

(23)

$16.39

Manufacturer Part Number:: 1313113

Genuine OEM replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most c...

Hex Jam Nut

★★★★★

(1)

$6.16

Manufacturer Part Number:: 902010201227S

This item has been sourced from the original manufacturer to be used with drill presses, band saws, sanders, bench grinders, lathes, radial arm saws, and finishing machines from Delta and Black & Decker. The metal nut is used with several different types of tools and the application of the nut can vary based on the model of the equipment.

Stud

$11.67

Manufacturer Part Number:: 424011110003S

Dust Chute

$56.51

Manufacturer Part Number:: 424020260001

Clamp

$25.90

Manufacturer Part Number:: 424020270010S

PLASTIC WASHER

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 803679

This is an authentic OEM component from Porter Cable. Made for use with many band saws, the plastic washer is fitted between the bearing and the pulley shaft. This protective item is sold individually. You will need a screwdriver for the repair.

Delta Chop Saw Parts

Top Delta Chop Saw Models

Popular Delta Chop Saw Parts

Delta Chop Saw Models

Delta Chop Saw Parts

Search By Model or Part Number

Top Delta Chop Saw Models

Popular Delta Chop Saw Parts

Delta Chop Saw Models