OEM Porter Cable Band Saw Parts & Accessories

MITER GAUGE ASSY – Part Number: 5140075-35

$6.28

Manufacturer Part Number:: 5140075-35

This is an original Porter Cable replacement part for the PCB330BS 14" band saw. The miter gauge assembly is a complete part, and no assembly is required. The miter gauge fits into the slot on the table, and no tools are required to install the part, the miter gauge assembly is sold individually.

SS/A HANDLE SET

★★★★★

(11)

$18.44

Manufacturer Part Number:: A03070

This is a Genuine OEM Sourced replacement part designed for use with Sanders and Band Saws. This item is made out of Plastic and it is Sold Individually. It includes Two (2) Pieces of the Knob. Please note the Screw used to secure this Knob is Sold Separately.

SWITCH

★★★★★

(8)

$33.90

Manufacturer Part Number:: N224532

This Trigger switch has 4 terminals and a locking mechanism on the trigger. This authentic Porter Cable replacement part is sold individually. rnrnSwitches are commonly replaced parts in power tools, handling all on/off and variable speed operations. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they will d...

WHEEL

★★★★★

(9)

$29.42

Manufacturer Part Number:: 5140075-34

Genuine Porter Cable Wheel Tire for Band Saw. This part is made out of Rubber and is Sold Individually. When putting the tire on a band saw Wheel, it may seem too small but it is not. Band saw Tires will typically come approximately 2 or more inches smaller than the Tire you're replacing. The old Tire stretches over time thus becoming less effective and eventually will break. Also, as Tire ages th...

BRUSH & RETAINER ASY

★★★★★

(1)

$16.68

Manufacturer Part Number:: 874289

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of t...

INSERT, TABLE

★★★★★

(5)

$13.16

Manufacturer Part Number:: 5140075-24

This is a genuine Hitachi table insert. It is supplied directly from original equipment manufacturer for use on compound miter saws. Table inserts reduce splintering and jamming of thin slices of wood between the blade and the plate. If an insert is missing or damaged it needs to be replaced. This item is made out of plastic material and it is sold individually.

WASHER

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 863134

This authentic manufacturer-sourced component is specially designed for use with Black and Decker, Porter Cable and DeWALT equipment. It helps to provide a tight seal between connected parts. This part provides an identical replacement for a missing or a faulty hardware that was included with a new unit. Please make sure to check the appropriate diagrams of your model for the exact location and ap...

TRUNNION

★★★★★

(7)

$12.08

Manufacturer Part Number:: 5140074-74

This is an authentic OEM sourced part which is designed for Porter Cable band saws. It is an important part of the mechanism which mounts the table and allows a user to adjust the cutting angle. Over time it may wear out or get damaged eventually requiring a replacement to ensure your equipment functions properly. Make sure to refer to the owners manual and the appropriate diagrams of your model f...

CORD

★★★★★

(9)

$37.79

Manufacturer Part Number:: 879182

This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 7 Feet Long • Porter Cable models: 6302 T4, 6902 T5, T6

WASHER

★★★★★

(2)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 803435

This is a genuine OEM sourced replacement part which is specially designed for use with portable band saws. It helps to distribute the pressure evenly and provide a tight seal between the connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable composite mat...

BEARING

$21.03

Manufacturer Part Number:: 803858

This needle roller style bearing is an OEM part. It is commonly found in band saws produced by Porter Cable, DeWALT, and Black & Decker. Bearings are used to diminish friction between moving parts while also securing rotational angle. They need replacing fairly often because of this high wear role. Sold separately.

RUBBER TIRE

★★★★★

(18)

$16.53

Manufacturer Part Number:: N887163

Porter Cable Band Saw Parts

Top Porter Cable Band Saw Models

Popular Porter Cable Band Saw Parts

Porter Cable Band Saw Models

Porter Cable Band Saw Parts

Search By Model or Part Number

Top Porter Cable Band Saw Models

Popular Porter Cable Band Saw Parts

Porter Cable Band Saw Models