OEM Black and Decker Belt or Drum Sander Parts & Accessories

$13.84

Manufacturer Part Number:: A23158

This is a genuine Porter Cable replacement part, it is sold individually. The purpose of the A23158 Dust Bag is to pick up dust and debris when using the Belt Sanders listed below. It is connected to the spout at the top of the Belt Sander Housing.

SS/A HANDLE SET

★★★★★

(11)

$18.44

Manufacturer Part Number:: A03070

This is a Genuine OEM Sourced replacement part designed for use with Sanders and Band Saws. This item is made out of Plastic and it is Sold Individually. It includes Two (2) Pieces of the Knob. Please note the Screw used to secure this Knob is Sold Separately.

GEAR

$44.90

Manufacturer Part Number:: 896468

This part is an OEM from the Porter Cable manufacturer. The metal gear is compatible with many belt sander devices. The gear is fitted between the nut and the ring, helping to rotate the drive belt. A screwdriver is needed in the repair. This component is sold individually.

SHOE ASSY

★★★★★

(8)

$57.05

Manufacturer Part Number:: 908909

Genuine Porter Cable replacement part, this item is sold individually. The 4" Shoe Assembly attaches to the base of the 4x24 Belt Sanders listed below. The purpose of this part is to allow the sanding belt run against it, it helps to create a smooth flat sanded surface. It includes the metal platen cork & three mounting screws. Over time the platen and cork will start to wear. It should be replace...

KNOB

★★★★★

(1)

$6.16

Manufacturer Part Number:: 897159

Genuine OEM replacement part used on Belt Sanders. it is Sold Individually. This part consists of a Plastic Knob with a Metal Threaded Shaft. This part in conjunction with a Spring will allow you to Adjust Belt Tracking by turning the Knob in either direction until the edge of the belt is even with the outer edge of the rear rubber-covered pulley. Replacing this part is very easy and it does not ...

BEARING,NEEDLE

★★★★★

(1)

$25.04

Manufacturer Part Number:: 804211

This is a genuine replacement steel bearing from original manufacturer. It is commonly used in Porter Cable and Black & Decker belt sanders. Bearings are parts which separate metal parts to ease in movement and reduce friction. They also stabilize and prevent incorrect direction/tilt during movement. These high-wear parts are replaced regularly. This part is sold individually. Washers etc. sold separately.

Power Cord (10-foot)

★★★★★

(6)

$29.34

Manufacturer Part Number:: 330072-97

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

BELT

★★★★★

(26)

$9.24

Manufacturer Part Number:: 491937-00

This is a genuine OEM replacement part. Package includes one belt. It is placed around the segmented drive pulley and the segmented driven pulley. Its purpose is to drive the sanding belt and sanding disc, on the machines listed below.

Belt

★★★★★

(5)

$10.67

Manufacturer Part Number:: 587263-00

This is a genuine OEM sourced replacement belt used on Bosch sanders. This is the main drive belt for the unit. This item is made out of rubber and it is sold individually. It is recommended to replace these belts every 6 months to ensure optimum performance. You would need a screwdriver to complete a repair. • Remove the belt cover • Replace the old belt with the new one • Secure the housing

BRUSH & SPRING

★★★★★

(5)

$10.73

Manufacturer Part Number:: N031635

Genuine Porter Cable replacement part includes 1 Carbon Brush with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear ite...

Dust Bag Assembly

★★★★★

(7)

$19.95

Manufacturer Part Number:: 588562-00

This dust bag assembly is a genuine OEM replacement part, it is not an aftermarket imitation. This high quality item is made for use with Dewalt and Black and Decker sanders. The purpose of this bag is to collect the dust picked up by sander. It is made with strong fabric material with a plastic collar. It has a zipper for quick and easy clean up. Please note, one dust bag assembly is included per...

Terminal

★★★★★

(2)

$6.16

Manufacturer Part Number:: 683784

The terminal is made out of metal. This item is available as an individual replacement part. It is a genuine DeWALT, Black & Decker, and Porter Cable part sourced directly from the manufacturer for use in saws, drills, engines, grinders, nibblers, routers, sanders, and shears. A set of pliers may be required to replace this item. This part may become broken and will need to be replaced.

Black and Decker Belt or Drum Sander Parts

Top Black and Decker Belt or Drum Sander Models

Popular Black and Decker Belt or Drum Sander Parts

Black and Decker Belt or Drum Sander Models

Black and Decker Belt or Drum Sander Parts

Search By Model or Part Number

Top Black and Decker Belt or Drum Sander Models

Popular Black and Decker Belt or Drum Sander Parts

Black and Decker Belt or Drum Sander Models