Porter Cable Angle Grinder Parts
We sell only genuine OEM Porter Cable ® parts.
Top Porter Cable Angle Grinder Models
-
Porter Cable PC750AG (Type 1) 7.5 Amp Small Angle Grinder Parts
-
Porter Cable PCC761B (Type 1) 20V Grinder Angle Grinder Parts
-
Porter Cable PCEG011 (Type 1) 6.0-Amp 4.5-In Small Angle Grinder Parts
-
Porter Cable PCEG011 (Type 10) 6.0-Amp 4.5-In Small Angle Grinder Parts
-
Porter Cable PCCG400B (Type 1) Angle Grinder Parts
-
Porter Cable PCB575BG Bench Grinder Angle Grinder Parts
-
Porter Cable PC60TPAG (Type 1) 6.0 Amp Angle Grinder Parts
-
Porter Cable PCB525BG (Type 1) Bench Grinder Angle Grinder Parts
.png)
Popular Porter Cable Angle Grinder Parts
- Manufacturer Part Number:
- 5140014-98
Genuine Manufacturer Sourced replacement part designed for use with some Angle Grinders. This part is made out of Carbon with a Lead Wire attached. This item includes One (1) Carbon Brush per order. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will ...
- Manufacturer Part Number:
- 5140014-93
It is a genuine OEM sourced item which is specially designed for use with Black and Decker, Porter Cable and Dewalt grinders. This part helps to secure the grinding disk to the shaft, please make sure to refer to the owners manual for the correct application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually. Please note the outer flange and the...
- Manufacturer Part Number:
- 633044-00
This is an authentic manufacturer sourced replacement part designed for use with Dewalt grinders. It helps to provide an air tight seal for the gearbox. It is made out of rubber material and it is sold individually. To complete this repair you will need a spanner wrench.
- Manufacturer Part Number:
- 330072-98
Length: 8'
Gauge: 18
Wires: 2
Type: Bare Wire
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...
- Manufacturer Part Number:
- N263699
This authentic manufacturer-supplied washer is specially designed for use with DeWALT angle grinders. It is a special hardware that helps to provide a tight seal between connected components. This is an identical replacement for a missing or a damaged O-ring that was installed on a new unit. One durable rubber part is included. Refer to the appropriate diagrams for your model to ensure the proper ...
- Manufacturer Part Number:
- 562210-00
This item is an authentic DeWalt replacement part that has been sourced from the original manufacturer to be used with angle grinders and masonry saws. In grinders, the metal spring is used to provide compression for the spindle lock pin. In masonry saws, the spring provides a similar function for the depth adjustment lever lock pin. This item is sold as an individual replacement part.
- Manufacturer Part Number:
- 5140005-34
This is an original replacement part manufactured for use with angle grinders. The special metal flange sits above the grinding wheel, and provides space between the wheel and guard. This inner flange is sold individually.
- Manufacturer Part Number:
- 330072-97
This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long
- Manufacturer Part Number:
- N119639
- Manufacturer Part Number:
- 596440-00
This replacement wrench is a genuine OEM approved part that is used with Dewalt, Black and Decker and Porter Cable agnle grinders. It is used to tighten or remove the outer flange which secures the grinding wheel. Please note this durable metal wrench is sold individually.
- Manufacturer Part Number:
- 605040-15
Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.
- Manufacturer Part Number:
- 5140014-92
It is a genuine OEM sourced replacement outer flange that is utilized on Black and Decker, Porter Cable and Dewalt grinders. This part helps to secure the grinding disk to the shaft. A spanner wrench which is sold separately is used to tighten and loosen this hardware. It is made from high quality metal and it is sold individually.
Porter Cable Angle Grinder Models
-
Porter Cable PC750AG (Type 1) 7.5 Amp Small Angle Grinder
-
Porter Cable PCC761B (Type 1) 20V Grinder Angle Grinder
-
Porter Cable PCEG011 (Type 1) 6.0-Amp 4.5-In Small Angle Grinder
-
Porter Cable PCEG011 (Type 10) 6.0-Amp 4.5-In Small Angle Grinder
-
Porter Cable PCCG400B (Type 1) Angle Grinder
-
Porter Cable PCB575BG Bench Grinder Angle Grinder
-
Porter Cable PC60TPAG (Type 1) 6.0 Amp Angle Grinder
-
Porter Cable PCB525BG (Type 1) Bench Grinder Angle Grinder
-
Porter Cable 7410 (Type 1) Right Angle Grinder
-
Porter Cable 7408 (Type 2) 4-1/2 Inch Angle Grinder
-
Porter Cable 7412 6 Inch Angle Grinder
-
Porter Cable 7406 (Type 4) 4-1/2 Inch Angle Grinder
-
Porter Cable 7406 (Type 3) 4-1/2 Inch Angle Grinder
-
Porter Cable PTX4 Air Angle Grinder
-
Porter Cable J-7410 (1) Flex Tadpole Angle Grinder
-
Porter Cable PCE810 (Type 1) 4-1/2 Smll Ang Gri Angle Grinder
-
Porter Cable PC60TAG (Type 1) 6.0 Amp Angle Grinder
-
Porter Cable 7430 4.5" Angle Grinder
-
Porter Cable PC1800AG (Type 1) 18V Cut-Off Tool Angle Grinder
-
Porter Cable PC18AG (Type 1) 18V Bare Cut-Off Tool/Angle Grinder
