OEM Bostitch Miscellaneous Parts & Accessories

PISTON STEM

$55.57

Manufacturer Part Number:: BC1455

This OEM sourced replacement part designed for Bostitch nailers/staplers. The piston stem is the part of the nail gun that drives the piston. The drivers do have a tendency to bend or break if not used correctly or if you are driving nails into extra hard material. This item is made out of metal and it is sold individually. To help extend the life of a pneumatic tool use the specified oil in it d...

SEAL

★★★★★

(7)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 180446

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with pneumatic nailers and staplers. The seal is used to prevent leaks between the head valve and the end cap spacer. This item is available as an individual replacement part.

PISTON RING

★★★★★

(14)

$6.16

Manufacturer Part Number:: N905972

Genuine OEM replacement part, this item is sold individually. The purpose of this part is to keep air pressure in the cylinder of the tools listed below. If you have an air leak in your pneumatic tool it is a good practice to replace the O-ring and seals.

O-RING-.487X.103

★★★★★

(4)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 850143

Genuine Bostitch replacement part, this part is sold individually. The purpose of this O-Ring is to create a seal around the Piston Stem of the Bostitch Floor Nail Guns shown below. Over time O-Rings can wear and become brittle or stretched. When your Nail Gun becomes sluggish or the Driver won't retract, it may be time to tear the Gun down and inspect all of the O-Rings and Seals.

SLEEVE-CYLINDER

$6.16

Manufacturer Part Number:: 180458

This item is available as an individual replacement part. The cylinder sleeve fits between the piston driver assembly and the check seal. This part is an original part from Bostitch for use in nailers and staplers. It is made out of plastic and will require replacing if it breaks. A set of pliers and an allen wrench may be needed when replacing this sleeve.

GASKET-END CAP

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 180463

It is a genuine manufacturer-approved replacement gasket which is specially produced for use with Bostitch nailers and staplers. This gasket provides an air-tight seal for the end cap. over time it may wear out and crack eventually requiring a replacement. It is a high-quality component which is made of durable composite material and it is sold individually.

STEM-PLUNGER - MII

$34.15

Manufacturer Part Number:: BC703

This is a genuine Bostitch replacement part. The plunger is supplied from the original equipment manufacturer for use with pneumatic nailers and staplers. It is an important component which pushes the driver. Over time it may wear out or get damaged eventually requiring a replacement. Note, this high-quality component is made of durable metal and is sold individually. Make sure to check the approp...

BUMPER

★★★★★

(1)

$13.28

Manufacturer Part Number:: 180461

This genuine OEM bumper in your nailer absorbs the impact and provides cushioning when the piston retracts after driving a nail. It is seated at the bottom of the nail gun cylinder. Due to the repeated stress it undergoes during operation, the bumper wears out gradually. Signs that suggest the need for bumper replacement include unusual noises, reduced driving power, misfires, or visible damage to...

O-RING-44.7MMX2.4MM

★★★★★

(4)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 180459

This replacement part is supplied directly from the original equipment manufacturer for use with Bostitch nailers and staplers. It is utilized to provide an air-tight seal for the cylinder sleeve, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable part is made of high-quality rubber and is sold individually.

BUMPER

★★★★★

(9)

$50.01

Manufacturer Part Number:: 105043

This is a Genuine Manufacturer Sourced replacement part used on certain Bostitch Stapler/Nailer. This item is made out of Resin and it is sold individually. The purpose of this Piston Bumper is to keep the piston from hitting the bottom of the cylinder and damaging it. Because this part get so much abuse it has a tendency to crack and fall apart. If you see and parts of this bumper falling from yo...

Trigger Valve

★★★★★

(3)

$12.29

Manufacturer Part Number:: 9R202265-TW

This genuine OEM trigger valve in your nailer or stapler works in conjunction with the head valve. When you press the trigger valve, it creates a pressure difference between the air reservoir and the cylinder and causes the head valve to open and release compressed air to drive the nail or staple into the material you are working on. It is commonly found in the handle or grip area of the tool. If ...

O-RING-.614X.070

$25.71

Manufacturer Part Number:: 850144

This is a Genuine Manufacturer Approved replacement part used on specific Bostitch Nailers. This is a Rubber Ring and it is sold individually. O-rings are designed to withstand thousands of pounds of pressure by creating a seal between two or more parts. Over time O-Rings will damage and should be inspected periodically. If parts are showing signs of wear they should be replaced.

Bostitch Miscellaneous Parts

Top Bostitch Miscellaneous Models

Popular Bostitch Miscellaneous Parts

Bostitch Miscellaneous Models

Bostitch Miscellaneous Parts

Search By Model or Part Number

Top Bostitch Miscellaneous Models

Popular Bostitch Miscellaneous Parts

Bostitch Miscellaneous Models