OEM Dynabrade Drill Parts & Accessories

Throttle Lever Assy., Safety L

$69.01

Manufacturer Part Number:: 01950

This part has been OEM sourced and is intended to be used with buffers, sanders, right angle reciprocating filers, and die grinders from Dynabrade. The metal lever assembly includes the safety lock and attaches to the body of the tool. This item is used to actuate the valve stem to allow compressed air into the tool to drive the rotor. The throttle lever assembly is sold as an individual replacement part.

Blades/rotor (4 Pack)

$48.34

Manufacturer Part Number:: 01011

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are vi...

Bearing

$33.00

Manufacturer Part Number:: 02649

This authentic replacement part is designed for use with Dynabrade power tools. Ball bearings are used to reduce friction between rotating parts. It is one of the bearings for the rotor. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Over time bearings may begin to wear out compromising tools functionality and eventua...

Vanes (4/pkg.)

$46.88

Manufacturer Part Number:: 01185

This is an authentic component which is sourced directly from the original equipment manufacturer for use with Dynabrade equipment. This part is made of layered fabric and laminate and is used to spin the rotor. This part is designed to slowly wear down over time, to avoid damage to the cylinder. It is advisable to replace all the rotors at the same time for even wear. Keep in mind these high-qual...

Bearing

$39.18

Manufacturer Part Number:: 02696

This authentic component is supplied by the original manufacturer for use with Dynabrade power tools. Ball bearings are generally utilized to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Bearings experience constant wear from pressure, heat, vibration and friction, ev...

Tip Valve

$17.66

Manufacturer Part Number:: 01472

This is a genuine OEM part. The Dynabrade tip valve is manufactured for use with orbital sanders, finishers and grinders. This metal and plastic valve often sits in the air inlet bushing, and is supported by a spring. The valve is sold individually, please see specific manual for additional repair information. A pair of pliers, wrench and a screwdriver may be necessary for installation.

Muffler Cap

$13.88

Manufacturer Part Number:: 56028

This is an authentic OEM component from Dynabrade. The plastic muffler cap is compatible with many sander devices. Fitted in the muffler assembly, the part secures the muffler insert. This part is made to help decrease the exhaust noise and capture any excess oil. The muffler cap is sold individually. A wrench and a screwdriver may be needed for the installation.

Felt Silencer

$6.49

Minimum Quantity of 2 required

Manufacturer Part Number:: 04078

This felt silencer is supplied directly from the original equipment manufacturer. The Dynabrade part is compatible with a variety of different power tools and appliances. This item is fitted between the lock ring and the air control ring, minimizing the noise. The felt silencer is sold individually. For the repair, you may need a wrench and pliers.

Blades

★★★★★

(2)

$46.08

Manufacturer Part Number:: 01480

These authentic OEM sourced replacement rotor blades are commonly used on Dynabrade sanders and grinders. They are attached to the rotor inside the tool pushing the air. This set includes (4) compound material blades per order. Replacing these blades you will need a set of wrenches and pliers.

Seal

★★★★★

(1)

$9.79

Manufacturer Part Number:: 01464

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench...

Bearing

$33.72

Manufacturer Part Number:: 01007

This is an original part assembled by the original manufacturer. It is compatible with various Dynabrade handheld power tools, such as grinders and finishers. Ball bearings are used to buffer between moving parts. They also serve to keep parts correctly positioned while assuring steady directional movement. Ball bearings need frequent replacement because of this high-wear role. This steel part is sold individually.

O-ring

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 95730

It is a genuine replacement o-ring which is supplied by the original equipment manufacturer for use with Dynabrade power tools. This item is utilized to provide an air-tight seal between connected parts, please make sure to check appropriate diagram of your model for the correct use and location of this component. Over time o-rings tend to deteriorate and crack eventually requiring replacement to ...

Dynabrade Drill Parts

Top Dynabrade Drill Models

Popular Dynabrade Drill Parts

Dynabrade Drill Models

Shop by Popular Dynabrade Drill Part Types

Dynabrade Drill Parts

Search By Model or Part Number

Top Dynabrade Drill Models

Popular Dynabrade Drill Parts

Dynabrade Drill Models

Shop by Popular Dynabrade Drill Part Types