This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Troubleshooting
This part works with the following brands:
DeWALT
This part works with the following products:
Chop Saw
Table Saw
Part# N558583 replaces these:
N039389,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(5 Reviews)
Click to filter by ratings:
5 stars
5
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great parts
arrived very quickly. Thanks
Guest - June 5, 2019
Verified Purchase
★★★★★
★★★★★
Just what I needed
The chop saw used on the job went to acting acting weak like it had lost a lot of power and smoking some. Ordered new carbon brushes for it and now the saw works like new again. Excellent prices and fast service. I always come shopping at ereplacement parts when I need help to get my tools up and running again. Thank you for the great service!
Guest - July 27, 2019
Verified Purchase
★★★★★
★★★★★
Easy Fix thanks for the sale and fast shipping
Work great, fast shipping and parts are good, easy fix for chop saw
Guest - October 22, 2019
Verified Purchase
★★★★★
★★★★★
easy rerpair
it worked great, the saw runs like new
Guest - March 24, 2021
Verified Purchase
★★★★★
★★★★★
Easily ordered and repaired
Carbon brushes were easy to locate on the site and arrived quick.
Guest - June 17, 2021
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Removed the rear motor cover with a torx screwdriver 2 screws. Remove the brush retainer caps, remove the old brushes, install the new brushes, reinstall the brush retainer caps & rear motor cover.
I removed the brush caps with a screwdriver, then I removed the worn brushes, and installed the new brushes. I then screwed the brush caps back in. Easy fix.
With a screwdriver remove the the brush caps, Then remove the worn brushes. Clean out the brush holders with compressed air and inspect the armature for any signs of damage. Then install the new brushes in the holder and screw the brush caps back on.
Easy, use a screwdriver off take the end cap. Then remove the brush caps with a screwdriver. Then pull the worn brushes out, and install the new ones. Replace the brush caps and the end cap. And your done. I would recommend ereplacement parts to anyone.
1. Removed end cover (2 screws)
2. removed brush holder caps and remove old brushes.
3. Loosen set screw holding brush holder. Removed the warped brush holder with pliers & screwdriver. Case was slightly warped due to the excess heating so the holder came out in several pieces.
4. Clean rotor contacts with electrical con
... Read moretact cleaner to remove carbon buildup.
5. Used small file to smooth out case sides for new brush holder to fit back in. Inserted new holder and tighten set screw back down.
6. Install new pair of brushes and holder caps. Reinstall end cap.
7. Test ran chop saw to ensure a good repair.
1. Removed the original carbon brushes.
2. Cleaned the motor with spray type electrical cleaner.
3. Places order for new brushes
4. Upon receipt, checked new parts for correctness and or damage
5. Installed new brushes
6. Performed test
7. Test Satisfactory.
Have a problem with brush wire connector. The wire end was bunt and a new end was installed
which does not hold well , in use it comes off . Have go back into saw to fix . No part number for the right kind of connector .
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
