OEM DeWALT Circular Saw Parts & Accessories

$8.20

Manufacturer Part Number:: 605040-27

This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on the tool and allows it to run smoothly. • Bearings experienc...

Power Cord

★★★★★

(18)

$40.24

Manufacturer Part Number:: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Dust Bag Assembly

★★★★★

(7)

$12.08

Manufacturer Part Number:: N273733

This authentic OEM dust bag assembly is sourced from the original manufacturer for use in sanders. It consists of a fabric bag and plastic cap measuring approximately 5.5 inches in length and 2.5 inches in diameter. The bag assembly collects the dust and debris that is produced during sanding allowing you to maintain a clean and safe working environment. Over time the bag may tear or wear down, le...

Blade Bolt

★★★★★

(10)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 648697-00

This is a genuine manufacturer sourced replacement part designed for use with Dewalt circular saws. It is used to secure the blade to the spindle/shaft. This part is made out of metal and it is sold individually. Requires a wrench or a hex key/allen wrench to tighten/loosen this screw.

Bolt

★★★★★

(6)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 145344-00

This is an OEM part sourced directly from the manufacturer. The screw is found in Craftsman circular saws. This is a metal part, used to hold other components to the spindle assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

Carbon Brush With Spring

★★★★★

(10)

$11.84

Manufacturer Part Number:: 450374-12

Genuine OEM replacement This brush is sold individually, 2 are needed for most every electric power tool It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the...

Outer Clamp Washer

★★★★★

(5)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: N621119

This outer clamp washer is specially designed for use with Dewalt circular saws. It is an authentic item supplied directly from original equipment manufacturer. This washer helps to secure saw blades to the spindle-shaft. Includes one (1) metal outer clamp washer per order. Please note, the inner clamp and the blade bolt are both sold separately. You will need a wrench to remove and install the b...

Ball Bearing

★★★★★

(9)

$23.41

Manufacturer Part Number:: 605040-20

This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bear...

Brush and Spring

★★★★★

(45)

$13.84

Manufacturer Part Number:: 145323-06

This Genuine OEM carbon brush is an essential replacement part designed for use with a variety of DeWALT and Black & Decker saws. Sold individually, this high-quality component is made to conduct electrical current within the motor, enabling efficient power transfer and tool performance. Over time, carbon brushes naturally wear down due to friction and electrical contact, which can lead to intermi...

Brush

★★★★★

(34)

$21.37

Manufacturer Part Number:: 381028-08

Sold Individually. This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.

Carbon Brush With Holder

★★★★★

(20)

$12.62

Manufacturer Part Number:: 132254-07

Genuine Dewalt replacement part, this item is sold individually. It is used on all the tools shown below. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items...