OEM Porter Cable Nailer Parts & Accessories

EXHAUST DEFLECTOR – Part Number: P0590000200

$6.16

Manufacturer Part Number:: P0590000200

This is a Genuine OEM sourced replacement part designed for use with Staplers/Nailers. With this Exhaust Cover you can divert the air in any direction you want. It is made out of Plastic and it is Sold Individually. Please note Flange Nut used to secure the Cover is Sold Separately. To replace this item you would need a Hex Key/Allen Wrench.

O-RING

★★★★★

(56)

$6.79

Minimum Quantity of 2 required

Manufacturer Part Number:: A00104

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling • O-ring has ragged, tattered edges. These are commonly cau...

URETHANE RETAINER

★★★★★

(38)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 890725

This is a genuine Porter Cable replacement part, it is sold individually. The purpose of the 890725 Retainer is to secure the pins used on the model numbers shown below. It is advised to check the condition of the retainer often, for the reason the do deteriorate over time and can fall off of the pin they are retaining.

O-RING

★★★★★

(5)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: S06P001500

This is a Genuine Manufacturer Sourced replacement part designed for Nailers/Staplers. This O-Ring provides an Air-Tight Seal for the Valve Piston. Over time this O-Ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of Rubber and it is Sold Individually. Replacing this item you would need Hex Key/Allen Wrench and Pliers to replace this item.

SEAL

★★★★★

(32)

$16.06

Manufacturer Part Number:: 904689

Genuine Porter Cable replacement part, this item is sold individually. The Head Valve Seal is in stalled on top of the 904695 Cylinder. It provide a seal for the Head valve. If you air leaks in your nail gun you may consider the part number 904949 Overhaul Kit. It includes the Head Valve Seal and other internal parts to stop air leaks

O RING

★★★★★

(6)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 180448

This is an authentic Bostitch replacement part used on specific Nailers. This is a Rubber Ring and it is sold individually. O-rings are designed to withstand thousands of pounds of pressure by creating a seal between two or more parts.

PROTECTIVE COVER

★★★★★

(10)

$6.16

Manufacturer Part Number:: 884443

Genuine OEM replacement part, this item is sold individually. The purpose of the 884443 Protective Cover, is to cover the air inlet coupler, to keep dust and debris from getting inside the Nail Gun or Stapler and contaminating the internal parts. You should cover the coupling when the tool is not being used. They do have a tendency to wear out, it may be a good idea to have one or two extra on hand.

PISTON DRIVER

★★★★★

(6)

$16.68

Manufacturer Part Number:: 180205-K

Genuine OEM replacement part, this item is sold individually. The main purpose of the 180205 Piston/Driver is to strike the fastener in the nose of the nail gun into the material you are nailing. At times this part can bend or break and it will have to be replaced. When you purchase this item it does not include the part number, 180457 Piston Ring.

KIT-TRIGGER VALVE

★★★★★

(31)

$51.38

Manufacturer Part Number:: TVA6

This is a genuine Bostitch replacement part that fits all BT brad nailers and all S32 staplers. If trigger leaks air or if tool misfires often, try replacing trigger valve. This kit contains one (1) each of: valve assembly (including both O-rings), lubricant, spring pin punch, and repair instructions. Please note that two (2) O-rings are included but can also be purchased separately as parts # 106...

Grommet

★★★★★

(13)

$6.16

Manufacturer Part Number:: 391814-00

This special grommet is an original part which is specially designed for use with DeWALT and Porter Cable staplers and nailers. It is utilized to secure the pin that holds the adjuster. This is a high-quality replacement for a damaged or a missing grommet that was installed on a new unit. To ensure the correct location and application of this part, refer to the appropriate diagrams of your model. ...

PISTON RING

★★★★★

(14)

$6.16

Manufacturer Part Number:: N905972

Genuine OEM replacement part, this item is sold individually. The purpose of this part is to keep air pressure in the cylinder of the tools listed below. If you have an air leak in your pneumatic tool it is a good practice to replace the O-ring and seals.

HEAD VALVE BODY

★★★★★

(147)

$6.16

Manufacturer Part Number:: 180450-S

This is an original part from Craftsman for nailers and staplers. This part produces air pressure to force the driver in the direction of the fastener. You will need a allen wrench set, adjustable wrench and a screwdriver to replace this part. This part is made of plastic and sold individually.

Porter Cable Nailer Parts

Top Porter Cable Nailer Models

Popular Porter Cable Nailer Parts

Porter Cable Nailer Models

Shop by Popular Porter Cable Nailer Part Types

Porter Cable Nailer Parts

Search By Model or Part Number

Top Porter Cable Nailer Models

Popular Porter Cable Nailer Parts

Porter Cable Nailer Models

Shop by Popular Porter Cable Nailer Part Types