Easy
15-30 minutes
Multi Bkt Assembly 22-504-0002
OEM part for: Pro Temp, Heat Stream, Heat Hog, Master
Part Number: 22-504-0002
$29.89
Factory Backorder
Date Available: Unknown 
Compatibility
This Multi Bkt Assembly will fit the following 38 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Displaying 20 of 38 matching models.
38 total model matches. Try the above search to narrow your results.
This is the official OEM part for the following brands:
- Heat Hog
- Heat Stream
- Master
- Pro Temp
This item works with the following types of products:
- Heater
This part replaces obsolete part #: 22-603-0001, 22-504-0003
Repair Videos ?
Watch the Repair Video for
Multi Bkt Assembly
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
1
4 stars
1
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Heater part
Very fast and received the correct part. Thanks.
Guest -
December 9, 2020
Verified Purchase
gas heater parts
The parts were exactly I ordered, and delivery was quicker than expected.
Guest -
December 15, 2022
Verified Purchase
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Multi Bkt Assembly
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Heater would not stay lit after holding igniter button in for a minute or more
William - January 2, 2017
👍 8 of 8 people found this instruction helpful
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
1. Removed bottom plate
2. Removed blower motor
3. Removed thermocouple unit
4. Compared to new assembly and found to be exactly the same
5. Installed new unit, screws etc.
2. Removed blower motor
3. Removed thermocouple unit
4. Compared to new assembly and found to be exactly the same
5. Installed new unit, screws etc.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Would not stay lit after 1 minute without holding in the knob
Lynn - October 17, 2016
👍 5 of 5 people found this instruction helpful
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Took the unit apart from the bottom first then pulled the fan out, all parts that needed to be replaced were accessible at this point, then just replaced each part with the new parts
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Heater would ignite but not stay lit
Fred - February 25, 2016
👍 5 of 6 people found this instruction helpful
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
First choice was thermocouple but ended up being PCB board. To test, jumper two wires on control board going to gas valve. Small relay on board defective. Stayed on with jumper, replaced board, problem solved.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Propane heater would not stay burning
Christooher - January 21, 2023
Tool Type
Heater
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
1. Remove 4 screws holding black fan guard and fan from rear of heater
2. Pull fan guard and fan out from the housing. ( carful the 2 fan wires are attached.
3. Look inside and you will see the igniter and thermocoupler remove the 2 screws.
4. Take note of the 4wires on this. They should match the new part. Remove the 4 wires.
5. Remove 2 screws on the bottom of the unit and the face plate.
6. Pull the 4 wires through the rubber grommet. Take note of their location. And remove wires from their clip or screw holder.
7. At this point you are ready to instal new part. Simply repeat steps in reverse.
8. Before installing fan. Make sure all wires are zip tied and out of the way of fan blade. Or they will contact the fan.
9. Hook up propane and test heater for proper function and leaks.
2. Pull fan guard and fan out from the housing. ( carful the 2 fan wires are attached.
3. Look inside and you will see the igniter and thermocoupler remove the 2 screws.
4. Take note of the 4wires on this. They should match the new part. Remove the 4 wires.
5. Remove 2 screws on the bottom of the unit and the face plate.
6. Pull the 4 wires through the rubber grommet. Take note of their location. And remove wires from their clip or screw holder.
7. At this point you are ready to instal new part. Simply repeat steps in reverse.
8. Before installing fan. Make sure all wires are zip tied and out of the way of fan blade. Or they will contact the fan.
9. Hook up propane and test heater for proper function and leaks.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The heater would not stay lit / Thermocouple failed
David - January 28, 2020
Tool Type
Heater
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver
Parts Used
Disconnect power and gas connections
Removed the two screws from the bottom panel Unplugged the fan. Removee the four screws around the back and removed the fan. Unplugged the assembly from the botton. Remove the ground screw and remove the ground wire to the assembly. Remove the two screw holding the thermocouple assembly into the chasis, and ease the old thermocouple out of the chasis. Ease the wires out through the cabinet hole. Put the new thermocouple back in place being careful to position the wires where they will not interfere with the fan. Re-assemble everything reversing the steps above. Reconnect power and gas and tested unit. The replacement part works perfectly and the heater works as good as new.
Removed the two screws from the bottom panel Unplugged the fan. Removee the four screws around the back and removed the fan. Unplugged the assembly from the botton. Remove the ground screw and remove the ground wire to the assembly. Remove the two screw holding the thermocouple assembly into the chasis, and ease the old thermocouple out of the chasis. Ease the wires out through the cabinet hole. Put the new thermocouple back in place being careful to position the wires where they will not interfere with the fan. Re-assemble everything reversing the steps above. Reconnect power and gas and tested unit. The replacement part works perfectly and the heater works as good as new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Heater would not stay lite after hold down time .
Lowell - February 25, 2019
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Removed 4 screws at back of heater . Fan will come out with the grill . Remove 1 screw and remove the multi bkt assembly ( spark plug) . Then remove 2 screws that hold the bottom and remove it by prying it open at the screw end . Then just remove 1 wire at a time and replace with new wire . When all wires are replaced .Replace mba (spark plug) , bottom cover and fan -grill and your ready for some heat . Very easy if you remember to only take one (1) wire off at a time .
Thanks
Lowell
Old Guy's Wood Shop
Cedaredge CO.
Thanks
Lowell
Old Guy's Wood Shop
Cedaredge CO.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Learn MoreOur product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
