Medium
30-60 minutes
It is an authentic OEM sourced item which is specially produced for use with DeWALT drills and drivers. The magnet ring fits between the baffle assembly and the armature assembly. During the installation process, a screwdriver might be needed to replace this part. It may become broken and will need to be replaced. This is made of metal and is available as an individual replacement part.
Magnet Ring NA146883
OEM part for: DeWALT
Part Number: NA146883
$32.52
In Stock
Order within the next 13 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This Magnet Ring will fit the following 84 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
DeWALT
Show More Compatible ModelsThis item works with the following types of products:
- Drill Parts
- Hammer Drill Parts
This part replaces obsolete part #: N230576 (26mm), 648124-00
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Magnet Ring
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Burnt up. Magnetic ring seized to Armature
Loren - March 18, 2019
👍 1 of 1 people found this instruction helpful
Tool Type
Cordless Drill
Difficulty
Easy
Time
15-30 minutes
Tools Used
, Torx
Parts Used
Replaced Armature magnetic ring bearing holder
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Motor burnt
joe - December 9, 2018
Tool Type
Cordless Drill
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Torx screwdriver
Remove4 screws that hold chuck and gear assembly
Remove remaining screws holding clamshell together
Separate clamshell and gear assembly may need to pry a little bit be sure all screws are removed
Once separated u will need to remove bearing cap screws then lift out mag ring armature and brush assembly
Assemble in reverse order being cautious of mag ring clocking it only goes in on way with notch on the end facing chuck
This repair can be frustrating but with any mechanical ability it can be done and was well worth it my dewalt hammer drill works like new
Remove remaining screws holding clamshell together
Separate clamshell and gear assembly may need to pry a little bit be sure all screws are removed
Once separated u will need to remove bearing cap screws then lift out mag ring armature and brush assembly
Assemble in reverse order being cautious of mag ring clocking it only goes in on way with notch on the end facing chuck
This repair can be frustrating but with any mechanical ability it can be done and was well worth it my dewalt hammer drill works like new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Motor wouldn't run
Dennis - June 24, 2018
Tool Type
Cordless Drill
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver
1. Took handle apart - motor within handle
2. Removed screws holding armature in place
3. Lifted out armature and magnet housing
4. Brushes mounted in frame slot - removed by hand
5. Reversed removal -
Make sure the new brushes are mounted in the frame; assure speed selector and magnetic housing ring are positioned to go together at same time after armature has been set, gear end of armature fits into gear housing.
Watch trigger wiring when installing brushes; could get pinched in fwd-reverse switch.
2. Removed screws holding armature in place
3. Lifted out armature and magnet housing
4. Brushes mounted in frame slot - removed by hand
5. Reversed removal -
Make sure the new brushes are mounted in the frame; assure speed selector and magnetic housing ring are positioned to go together at same time after armature has been set, gear end of armature fits into gear housing.
Watch trigger wiring when installing brushes; could get pinched in fwd-reverse switch.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
