Easy
15-30 minutes
A genuine item which is supplied directly from the original equipment manufacturer for use with Campbell Hausfeld air compressors. The purpose of this gasket is to provide an air-tight seal for the inlet valve, over time it may wear out and even begin to crack eventually requiring a replacement. Keep in mind this high-quality component is made of durable composite material and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.
Gaskt-inlet Valve XA009500AV
OEM part for: Campbell Hausfeld
Part Number: XA009500AV
$5.13
In Stock
Order within the next 55 minutes and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This Gaskt-inlet Valve will fit the following 16 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Campbell Hausfeld
Show More Compatible ModelsThis item works with the following types of products:
- Compressor Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Gaskt-inlet Valve
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Needed new filter plugs over valves in cyl head
Richard - September 28, 2018
Tool Type
Compressor
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Wrench Set
Remove cover plate
Remove filters
Remove gasket from cover plate
Replace cover plate and gasket
Remove filters
Remove gasket from cover plate
Replace cover plate and gasket
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Air leak at air outlet cover
JAMES - September 7, 2017
Tool Type
Compressor
Difficulty
Easy
Time
15-30 minutes
Tools Used
Socket set
Removed head bolts. Removed air outlet bolts. Cleaned any existing old gasket material with putty knife, wire brush and fine grit wet/dry sand paper. Applied new gasket. No sealant. Assembled in reverse. New gasket did not seal, it was too thin. Proceeded to make my own gasket with a thicker gasket material I had laying around, it was twice as thick as the material used for the new one. Even the old one was thicker than the new one. Runs like new with no leaks. This air compressor is about 35 years old and has almost all original parts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
This was an old compressor maintenance issue. The intake cover was removed for inspection and screen cleaning. Gasket had been stuck and broke when removed. Intake has spider webs on screens.
James - July 13, 2017
Tool Type
Compressor
Difficulty
Easy
Time
30-60 minutes
Tools Used
Socket set, Putty knife , spray solvent , bench grinder with wire wheel
Removed intake metal plate which had 2 long hex head bolts. Took gasket out which was in very dry and brittle from heat and stuck in places to intake base metal. Sprayed brake cleaner solvent on gasket that stuck to head and bottom of plate. Scraped carefully softened gasket off with putty knife. Took intake cover plate and used a bench grinder wire wheel to clean bottom of plate. Reinstalled new gasket and reinstalled the two hex heads and carefully tightened them. The head plate was removed which had 5 small short hex head bolts and the same cleaning procedure was used with gasket surface cleaning and using grinder wire brush to remove residue on bottom of top plate. After cleaning reinstalled the new gasket and plate. Installed the five small hex head bolts and tightened in cross hatch pattern completed in less then 60 min.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
