eReplacementParts.com
877-346-4815
Electrolux Parts
Repair Parts Home
  
Appliance Parts
  
Electrolux Parts
  5303937183 Felt,seal Lower W/ Adh

Felt,​seal Lower W/​ Adh 5303937183

OEM part for: Electrolux, Frigidaire

Part Number: 5303937183


Install
Videos!
Felt,seal Lower W/ Adh - 5303937183:Electrolux 360 View
Felt,seal Lower W/ Adh - 5303937183:ElectroluxFelt,seal Lower W/ Adh - 5303937183:ElectroluxFelt,seal Lower W/ Adh - 5303937183:Electrolux 360 View
$35.15
In Stock
Order within the next 4 hours and your part ships today!
Medium 30-60 minutes (2 rated repairs)?
OEM: Original Equipment Manufacturer ?
ElectroluxFrigidaire
Does this fit my product?

Product Description ?

This is a felt seal for various models of dryers that is designed to ensure the dryer drum rotates smoothly. This felt seal adheres to the lower portion of the front panel of your dryer. This is only the lower felt seal which covers the bottom portion, as the top portion is sold separately, but this does include the necessary high temperature adhesive to adhere it. If your dryer is making excessive noise during its spinning cycles, it is worth inspecting the seal to check if it has worn out, which will happen over time and through regular use of your dryer. It is recommended that if you replace this seal, you replace the upper seal as well. To replace this seal, you will need a screwdriver and wrench, as well as a brush and putty knife or sharp tool to remove the previous seal and adhesive. Disconnect your dryer from power and access its interior using your screwdriver and wrench. Make sure to document where each wire harness attaches to so as to make the reassembly process easier. Unscrew, disconnect, and remove the front panel of your dryer and locate the seal(s) on the inside of the front panel. Use your putty knife or sharp tool to scrape off and remove the old seal(s). Use a brush to scrub away the excess adhesive left on the front panel and begin applying a light layer of adhesive around the perimeter of the panel where the previous adhesive sat. Apply the new seal and allow it to cure for up to 3 hours. To reinstall the panel, seat it in its original position and secure it with its screws, and then begin to rewire the dryer. Once the dryer is rewired, connect it to power and test the new seals.

  • Classification: Part
  • Weight: 0.16 lbs.
  • Shipping: Ships Worldwide

Compatibility

This Felt,​seal Lower W/​ Adh will fit the following 670 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.

Don't see yours? Try searching our site for :

This item works with the following types of products:

  • Dryer Parts

This part replaces obsolete part #: 134134700

Questions & Answers ?

Our customer Service team is at the ready daily to answer your part and product questions.

photo of team member
Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Questions & Answers for Felt,​seal Lower W/​ Adh


No questions have been asked yet

Customer Repair Instructions ?

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Medium 30-60 minutes (2 rated repairs)?

Noise while spinning

Steven - April 23, 2020
Tool Type

Dryer

Difficulty

Medium

Time

30-60 minutes

Tools Used

Screwdriver, Wire brush

Found a YouTube video for specific dryer, followed that. Wasn't that difficult.
Did you find this story helpful?
Thanks for voting and helping fellow customers!

everything was correct fit and form

ALan - April 9, 2020
Tool Type

Dryer

Difficulty

Medium

Time

30-60 minutes

Tools Used

Screwdriver, Nutdriver, none

Remove dryer to loop panel to access front panel screws removed front panel intentioned drun belt removed drum belt installed new nylon guide to front of drum,cleaned old felt runner from front panel and glued new runner guide to front panel both top and bottom install new rear be ar ing assy and grease,Installed new heating element to rear of cabinet and reassembled and yes of course cleaned and vacuumed any residue lint front the componants and cabinet interior.
Did you find this story helpful?
Thanks for voting and helping fellow customers!

OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.

Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.

Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.

All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.

This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.

eReplacementParts.com
7174 South 400 West
Suite 5
Midvale, UT 84047
visa mastercard discover american express PayPal