Medium
15-30 minutes
Door Assembly 7313220611
OEM part for: DeLonghi
Part Number: 7313220611
$28.67
In Stock
Ships within 1 business day 
Compatibility
This Door Assembly will fit the following 4 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
DeLonghi
This item works with the following types of products:
- Coffee Maker Parts
This part replaces obsolete part #: 7332180900
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Good parts
The part was exactly what I needed to repair my leaking coffee machine.
Joel -
November 29, 2021
Verified Purchase
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Door Assembly
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
The coffee chute was broken on door
Melvin - September 27, 2023
Tool Type
Coffee Maker
Difficulty
Hard
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Removed old chute from old door
Took new door and removed new chute and installed new chute on old door
Took new door and removed new chute and installed new chute on old door
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Coffee maker wasn’t serving water
William - February 10, 2023
Tool Type
Coffee Maker
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Generator:
1. Unplug machine, and remove side and rear panels
2. Losses wire bundles and disconnect electrical connections to circuit board
3. Loosen four mounting screws on top of generator. Secure nut and washer from below with fingers.
4. Disconnect hard tube fluidic connections from back and bottom by pulling out securing pins with pliers. Take care to remove o-ring from within connector
5. Pull rubber tube from side and remove old generator
6. Replace with new generator, and reinstall connections in reverse order. Holding the washers and nuts from underneath while threading bolts requires care. A small amount of grease can be used to stick the washer and nut to your finger.
7. Replace panels.
1. Unplug machine, and remove side and rear panels
2. Losses wire bundles and disconnect electrical connections to circuit board
3. Loosen four mounting screws on top of generator. Secure nut and washer from below with fingers.
4. Disconnect hard tube fluidic connections from back and bottom by pulling out securing pins with pliers. Take care to remove o-ring from within connector
5. Pull rubber tube from side and remove old generator
6. Replace with new generator, and reinstall connections in reverse order. Holding the washers and nuts from underneath while threading bolts requires care. A small amount of grease can be used to stick the washer and nut to your finger.
7. Replace panels.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Door would not stay closed.
Sandra - February 4, 2023
Tool Type
Coffee Maker
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
1 removed both sides of coffee machine to expose screws for front.
2 removed screws on both sides of the front
3 pried front out enough to grasp the hinge wire and pull it out, releasing the old door.
4 installed new door, replaced wire.
5 put screws back in front side, put sides back on and replaced screws.
6 Now the hard part! Door does not come with the cover. Had to work at removing the cover from the old door carefully, so as not to break the tabs on the cover. Essentially ending up breaking the tabs on the door piece to get it off.
7 Snapped old cover onto new door - and cancelled order for replacement.
1 New bean cover just snaps in easily.
2 removed screws on both sides of the front
3 pried front out enough to grasp the hinge wire and pull it out, releasing the old door.
4 installed new door, replaced wire.
5 put screws back in front side, put sides back on and replaced screws.
6 Now the hard part! Door does not come with the cover. Had to work at removing the cover from the old door carefully, so as not to break the tabs on the cover. Essentially ending up breaking the tabs on the door piece to get it off.
7 Snapped old cover onto new door - and cancelled order for replacement.
1 New bean cover just snaps in easily.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The black part with the two spout cracks eventually due to the high temperature liquid.
Joel - November 29, 2021
Tool Type
Coffee Maker
Difficulty
Medium
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
I only replaced the black piece with the two spouts and trashed the rest of the door assembly. I wish U could only buy that piece instead.
1. Open the door
2. There are two screws on top and one by the lock
3. With a flat screwdriver unlatch plastic the top and lock area
3. Remove the cover
4. Slide up the spouts piece
5. Slide in the new spout piece and assemble back the cover.
1. Open the door
2. There are two screws on top and one by the lock
3. With a flat screwdriver unlatch plastic the top and lock area
3. Remove the cover
4. Slide up the spouts piece
5. Slide in the new spout piece and assemble back the cover.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Door replacement due to cracked drip dispenser
Daniel - October 26, 2017
Tool Type
Coffee Maker
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
Removed all the covers screws to get to the hinge pin
holding the door. Remove the pin. Removed leaking door then installed the new door. Put the covers and tighten all the screws. Saved $100.00 plus two trips to repair
shop 30 miles away. Thank you Ereplacement
holding the door. Remove the pin. Removed leaking door then installed the new door. Put the covers and tighten all the screws. Saved $100.00 plus two trips to repair
shop 30 miles away. Thank you Ereplacement
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
